How to Sew Ribbons on Gaynor Minden Pointe Shoes? Very Easy Methods

How to Sew Ribbons on Gaynor Minden Pointe Shoes

Gaynor Minden pointe shoes are some of the most popular in the industry. They come in many different styles, colors, and sizes to meet every dancer’s needs.

While many dancers wear ribbon ties over their shoes to tie them onto the foot, some people choose to sew ribbons on so that they don’t have to worry about untying and retying them as they dance.

In this article, we will discuss how you can sew ribbons onto your Gaynor Minden pointe shoes.

How to Sew Ribbons on Gaynor Minden Pointe Shoes?.

There are several methods of sewing ribbons onto the shoe. You can use your sewing machine, hand sew it or even glue it. The techniques below will help you to choose the method for your shoes and also show you how to do it.

Ribbon Sewing Machine Method:

The ribbon sewing machine method is the easiest of all. You will need a regular sewing machine that can stitch a straight line.

Place the ribbon on your shoe and place a fabric strip underneath it to hold it in place. Sew along one end of the ribbon. Then sew another row of stitching beside the first to make a seam allowance for gathering later on.

Start sewing at the other end and keep going back and forth until you reach your starting point. Make sure to leave about ¼ inch between each line so that it is not too thick when gathered together.

Once finished, gather fabric using a gathering foot if available or by pulling a thread from opposite sides with fingers while holding the needle in place.

Hand Sew Ribbon Method:

You can sew it by hand also but make sure your stitches are small so they don’t show through from the other side. Use single strand thread or multi-strand floss depending on the width of ribbon you have chosen.

If using double stranded floss, then knot one end after inserting a needle into each end of the fabric strip underneath the shoe lining.

Use either stem stitch or backstitch with knots hidden understitching. Knots should always face upwards towards toes.

Ribbon Glue Method:

If you are using a non-glitter ribbon and can’t find any glittered double-stranded floss, then the only way to sew it in place is by glue. For this method, use either fabric or leather glue, so they don’t show through from the other side of the shoe.

To do this, simply put some glue on both ends and along between them and let it dry completely before wearing your shoes.

If you want glitter ribbons but don’t have access to a matching thread then just add some pearl strands into regular embroidery floss that matches the color of the ribbon.

Use a single strand for wider widths and a multi-strand if using narrow widths. Pearl strands should be knotted at each end with regular thread, so they don’t slip out of place.

As you can see, there are several options to choose from when it comes to sewing on ribbons, no matter which method you decide upon.

How do you cut the ends of a ribbon?

To prevent fraying, you can either use a heat gun or a lighter to melt the ends of the ribbon.

Or if there is no chance that it will come into contact with fire then just cut them using sharp scissors and seal edges by running over them with a hot iron so they don’t fray.

If sewing tapered ends after sewing the ribbon then you can use either fray check or clear nail polish to seal ends.

How long should Ballet ribbons be?

Depending on the size of the dancer’s foot and the width of the ribbon, length can vary from 12-18 inches.

The width should be the same as the shoe. Pointe shoes come in ¼”, ½” and ¾,” for beginners who choose narrower widths while advanced dancers use wider ones.

Now you have a rough idea about what type of ribbon to use, how to sew it on the shoe, and which method is best for your fabric.

Do pointe shoes need elastic?

Yes, they do. Pointe shoes come with single loop elastic and they should be sewn into the casing of the shoe to provide proper support.

Where do you put elastic on pointe shoes?

Elastic should be sewn into a channel that runs along the inside of a shoe from the arch to the heel.

How do you sew elastic on pointe shoes?

Using a regular sewing machine, run a single row of stitching close to the edge and tie off at both ends so it doesn’t come undone while wearing them.

If using a hand sewing method, make sure to knot at both ends before cutting excess thread.

Keep in mind that you should never sew elastic on the outside of shoes because it might show through your tights.

How do you seal elastic ends?

You can do it by simply running a lighter or hot iron over the ends so they don’t fray.

You can also use a fray check to seal them. If using clear nail polish, make sure it’s completely dry before wearing your shoes. To prevent elastic from sliding out of the shoe, sew one end to the inside seam.

If you are having trouble with keeping the ribbon attached, then try this trick by sewing a few stitches through the base of each side of the fabric strip.

For double-sided ribbons, use either single strand floss or multi-strand pearl threads and knot each end with regular thread so they don’t slip out of place.

To prevent the ribbon from sliding along the shoe, you can stitch it down at several points on both sides, making sure to run a row of stitches through the ribbon and just through the fabric on the other side.

To sew down folded over edges of the ribbon, use single strand thread for wider widths and multi-strand if using narrow widths. Pearl strands should be knotted at each end with regular thread, so they don’t slip out of place.

As you can see, there are several options to choose from when it comes to sewing on ribbons, no matter which method you decide upon. We hope that you found this useful!

Similar Posts